Do you know How To Start A Car With A Bad Ignition Switch? The first thing you need to do is find out if the problem is with the keyless ignition switch or not. How do you know? If your car won’t start and there’s no sign of a dead battery, it’s likely that the clutch has failed in some way. To confirm this, try turning the engine over by hand. If this doesn’t work, then it’s time to have the car towed for repairs.
If you cannot turn your key to start your car, you may need to replace your ignition switch. Replacing an ignition can be a little complicated due to its location near the steering wheel, so you will want to take your car to a mechanic.
If you’re feeling adventurous and have some basic automotive skills, you can try replacing the ignition switch on your own. Just make sure you have the right tools and that you’re aware of the possible dangers involved in this kind of repair work.
Step By Step Guide For How To Start A Car With A Bad Ignition Switch?
If you are experiencing any issues with your vehicle, then this guide will help teach you how to sidestep the ignition change so that it can be started effectively. All one needs are some appropriate tools, and they’ll have everything needed for an easy start. Following is the Step By Step Guide For How To Start A Car With A Bad Ignition Switch:
- Hotwiring
- The Drill And Screwdriver
- Jumper Links
Let’s explain them.
Hotwiring
If you are lucky enough to have a vehicle with an ignition system before the mid-90s, this is your best bet. When inside their car and locate the control wheel section that has every fundamental part within it. Next, take out all plastic covers from each inward area so they can get exposed as well.
Then find a wiring harness connector by itself, among other things like battery wire or connectors attached where necessary to strip down both ends together until there’s nothing left but bare copper strands wound tightly around one another in opposite directions.
After this, one should twist two strands around each other, being careful to do it correctly. After identifying which strand is positive and negative, connect each one to its own battery terminal by twisting each strand around the respective cable. Lastly, test out your work and try starting up the engine without all the unnecessary parts in the way.
The Drill And Screwdriver
You will need a keyhole, drill, and screwdriver. Start by drilling through the keyhole to break down its interior pins so that we may turn on our ignition with ease later in this process.
After drilling, push in a flathead screwdriver and turn it left to right while applying pressure with your whole body weight. The ignition switch will eventually turn off with every single attempt. Lastly, test out your work and try starting up the engine without any of its parts in the way!
Jumper Links
After opening the hood of your car, find and connect together two terminals with jumper links to get power flowing through them. One for starting up in case something goes wrong when trying to start it on its own, then just use this same link again once you’ve got everything running smoothly.
Next, locate an ignition switch which will allow either key or remote access into any engine bay at any time; remove this so only manual activation options remain available by taking out another screwdriver inserting past where they were before as far as possible towards their other end while pressing down lightly until clicking can be felt without further force applied.
At this time, it should be possible to start up your car as if everything was back to normal. If not, then use the jumper link option as a quick fix until you can get the ignition switch replaced by some helpful hands nearby.
Conclusion
If you’ve been looking for a way to start your car with a bad ignition switch, then read this article. That’s all we have on How To Start A Car With A Bad Ignition Switch?
Frequently Asked Questions
Can you start a car with a broken ignition switch?
Yes. A broken ignition switch won’t prevent the car from starting (though it will lock you out). You can free up the break with a screwdriver, credit card, or butter knife. Once you release the brake, start the gas and turn on the key. You’ll hear a clicking noise when it falls into position, and then your car should start like normal.
Can I jump my car if the ignition switch is bad?
No. If your ignition switch is bad, you won’t be able to deactivate the engine immobilizer, and it may turn back on when the battery is disconnected if it’s not disabled from doing so in a certain amount of time. Doing any work on that would have been much cheaper than buying a new car. If only you would have switched over your transmission fluid at least once already.
Can you bypass an ignition switch?
You can bypass it by cutting out the connection, or you could bypass it by using a basic electrical switch. The key thing to note is that this would be illegal because you’re tampering with running engine internals, and many manufacturers use this as an indicator of how healthy the car engine is, so there’s no way they’ll cover those repairs. You could just buy a new one instead, a much safer option.
Hi, I am Muhammad Daim – an automotive lover and researcher. I am a co-founder at AutomotiveGuider.com. I have a Bachelor’s Degree in Computer Science but cars and trucks have always been my passion. My goal is to always learn new skills and share my experience with the world.