How Much PSI Do I Need In My Rear Shock?

Proper suspension setup may be a crucial component of obtaining the simplest performance out of your cycle. Front suspension forks and rear shocks each need simple changes to work best for a selected rider, thus this data has relevance to riders of each hardtail and full-suspension mount for a mountain bike. Luckily, obtaining your suspension dialed in takes solely minutes if you follow the easy steps below. But How Much PSI Do I Need In My Rear Shock?

The exact PSI you finish up with depends on how plush/firm you would like the rear shock to be, however, an honest start line is one psi for 1 lb in weight of the rider (including riding gear).

Much PSI Do I Need In My Rear Shock

PSI In Different Components

PSI In Mountain Bikes

Start with the suggested gas pressure for your weight. If that’s not notable, try 100psi. On this fork, it’s the same l thought to be running 75psi for my weight however there was perpetually concerning 30mm unused travel. I born the pressure by 5psi, then another 5psi, ending up at 65psi.

PSI In The Front Shock

Set up the fork to a pressure wherever you’ve got between 25%-30% sag. Say, the amount the fork compresses after you get on the bike in a normal riding position needs to be sort of a fourth of the whole travel. If your Recon is 130mm travel, it ought to sink like 36-38mm with your weight on.

Pressure In MTB Shocks

As a rough guideline, you must aim for a sag of regarding twenty you look after the fork and half-hour for the rear shock. If yours is a smaller amount than that, you’ll be able to merely let some air out. If it’s over that, you’ll be able to add air with a shock pump counselled percentages or not: What matters most is that you simply feel comfy on your bike.

How Much PSI Should I Put Into My Suspension?

Many makers can have an instructed sag setting, but if not, we suggest a base setting of half-hour. If you need less sag merely add air to the shock, if you need additional sag lower the air pressure. Add air in ten psi increments and every time repeat the method till you reach the required sag.

What Pressure Should My Shock Be Under?

I’ve detected that as a general rule of thumb I ought to set the front shocks to 100 percent by weight in terms of psi, and also the rear shocks to seventy-fifth my weight (i.e., Front shocks at a hundred and ten psi and rear shocks at ~78 psi).

Conclusion

Now, after reading this article, you have the answer to this question, How Much PSI Do I Need In My Rear Shock? Shocks and struts facilitate stabilizing your vehicle’s movements, enhancing management once you flip, brake, accelerate or encounter uneven road surfaces. Today’s vehicles use shocks, struts, or a mix of the two.

Frequently Asked Questions

Do you want a rear shock lockout?

Usually, the only times you’d keep out your rear shock (or front fork) would be once on a long non-technical climb or on a different long distances ride. wheel suspension typically options multiple modes, to higher start the bike to climb or descend, and one among these common options is that they keep out.

How am I able to improve my rear suspension?

For anyone who wonders the way to improve the suspension on a truck, you’ll mate simply by simply following the steps lined during this article: Upgrade the shocks. Reinforce the leaf springs. Switch to larger wheels. Add a torsion bar. Use a raise kit. Add strut braces. Tune up the suspension.

Can I upgrade my rear suspension?

Upgrading the suspension on your wheel is one of the simplest belongings you will do to breathe new life into your bike. whether or not it’s a fork or rear shock, you may be astonied at the technology recently in suspension, and the way having a high-quality product offers you the boldness to shred more durable than ever before.

How much PSI is a Fox Float?

Hightower LT Fox Float DPX Rider Weight gas pressure Shock Sag 100lbs (45.5kg) 145 psi 16-19 mm 120lbs (54.4kg) 165 psi 16-19 mm 140lbs (63.5kg) 180 psi 16-19 mm.

Leave a Comment